stain guide

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro Solve (Solvent), Power Gel and ARA

PROCEDURE:

  1. Wet contaminated fibers with Gooff.
  2. Agitate gently but thoroughly to dissolve contamination.
  3. Allow dwell time (usually one to two minutes).
  4. Apply Power Gel to contaminated fibers.
  5. Again, agitate gently but thoroughly to emulsify dissolved contamination.
  6. Very thoroughly rinse area.
  7. Apply ARA to prevent re-soiling.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Amazing GOOFF (Solvent), Power Gel and ARA

PROCEDURE:

  1. Wet contaminated fibers with Gooff.
  2. Agitate gently but thoroughly to dissolve contamination.
  3. Allow dwell time (usually one to two minutes).
  4. Apply Power Gel to contaminated fibers.
  5. Again, agitate gently but thoroughly to emulsify dissolved contamination.
  6. Very thoroughly rinse area.
  7. Apply ARA to prevent re-soiling.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

 

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel.

CHEMICALS REQUIRED: Red Relief or Red 1.

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.

 

Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).

 

Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.

 

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE and Carpet Shark.

CHEMICALS REQUIRED: Dirt Chaser or Pro-Zyme(Digester), Stain Magic (Oxidizer) or OSR.

PROCEDURE: (Surface Contamination):

IMPORTANT:  Remember that blood is a biohazard. Protect yourself accordingly and treat it according to EPA guidelines.

  1. Mix Dirt Chaser or Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. If a visible stain remains apply Stain Magic.

 

PROCEDURE: (Sub-Surface Contamination):

You may experience wicking of blood on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad use steps 1-4 above and proceed with the following process.

  1. Mix OSR (Odor and Stain Remover) according to the directions on the bottle.
  2. Saturate the contaminated area being sure to apply enough OSR solution to penetrate the carpet backing and padding underneath.
  3. Allow up to 30 minutes dwell time.
  4. Use sub-surface flood extraction tool to remove moisture and oxidized contamination.
  5. Dry area as quickly and thoroughly as possible.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Power Gel and Last Step Rinse.

PROCEDURE:

  1. Scrape away excess contamination.
  2. Apply Power Gel liberally to spot.
  3. Agitate gently but thoroughly to emulsify compound.
  4. Rinse clean using a dilute solution of Last Step Rinse.

 

Tip: Solvents are not as effective as Power Gel on this substance.

TOOLS REQUIRED: HWE, Carpet Shark, steam iron, and clean terrycloth towel.

CHEMICALS REQUIRED: Power Gel.

PROCEDURE:

  1. If deposit is thick, scrape away excess wax from surface of deposit.
  2. Cover stain with dry towel.
  3. Heat spot with steam iron to dissolve wax(usually about 30 to 45 seconds) do not draw entire deposit into towelDoing so will drive the color from the was into the carpet fibers.
  4. After application of heat, promptly apply Power Gel to hot wax deposit and agitate gently with a Carpet Shark or bone scraper to put wax into solution with the Power Gel.
  5. Rinse area thoroughly using hot water extraction.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron or steamer and a terry towel.

CHEMICALS REQUIRED: Power Gel, Red Relief or Red 1.

PROCEDURE:

  1. Apply Power Gel to deposit to break down contamination.
  2. Allow 3-5 minutes dwell time.
  3. Clean stained area using hot water extraction.
  4. Blot area dry with clean white towel to remove excess moisture from carpet.
  5. Mix Red Relief Part A and Part B in equal parts (If using Red 1 follow usage instructions on the bottle)..
  6. Using trigger sprayer, wet stained fibers with Red 1 or Red Relief mixture.
  7. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  8. Apply steam heat from an iron set at the lowest steam temperature.
  9. Check the stain every 30 seconds.
  10. When the stain has turned to a light yellow or has disappeared remove heat and towel.
  11. Extraction rinse chemical residue away.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron or steamer and a terry towel.

CHEMICALS REQUIRED: Power Gel, Red Relief or Red 1.

PROCEDURE:

  1. Apply Power Gel to deposit to break down contamination.
  2. Allow 3-5 minutes dwell time.
  3. Clean stained area using hot water extraction.
  4. Blot area dry with clean white towel to remove excess moisture from carpet.
  5. Mix Red Relief Part A and Part B in equal parts (If using Red 1 follow usage instructions on the bottle)..
  6. Using trigger sprayer, wet stained fibers with Red 1 or Red Relief mixture.
  7. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  8. Apply steam heat from an iron set at the lowest steam temperature.
  9. Check the stain every 30 seconds.
  10. When the stain has turned to a light yellow or has disappeared remove heat and towel.
  11. Extraction rinse chemical residue away.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro Solve, Power Gel and ARA

PROCEDURE:

For latex or oil based caulking it’s best to remove the caulking from carpet before cleaning the area as water will dilute some of your chemical and reduce its effectiveness.

  1. Apply Pro Solve Gel liberally to caulking deposit.
  2. Allow 5 minutes dwell time.
  3. Gently agitate the spot with a Carpet Shark to break the caulking away from the fibers. (if necessary you can add more Pro Solve Gel at this time).
  4. Apply Power Gel and gently but thoroughly agitate to emulsify and suspend the Pro Solve and Caulking.
  5. Hot water extraction rinse leaving as dry as possible.
  6. Treat area with ARA to prevent resoiling.

TOOLS REQUIRED: HWE, Trigger Sprayer and Carpet Shark.

CHEMICALS REQUIRED: Power Gel and Stain Magic.

PROCEDURE:

  1. Dry vacuum area thoroughly to remove as much excess contamination as possible (this is very important).
  2. Apply dilute solution (15:1) Power Gel to contaminated fibers.
  3. Using Carpet Shark, agitate treated area until contamination becomes suspended in foam.
  4. Dry extract (no water) foam.
  5. Repeat steps 2 through 4 until foam no longer colors from substance.
  6. Thoroughly hot water extraction rinse area to remove Power Gel solution.
  7. If light color residue remains apply Stain Magic and allow dwell time. Stain will disappear as it dries.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) and Stain Magic (Oxidizer)

PROCEDURE:

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible.
  5. If a visible discoloration remains apply Stain Magic or Stain 1 to the discolored fibers.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE, Trigger Sprayer and Carpet Shark.

CHEMICALS REQUIRED: Power Gel and Stain Magic.

PROCEDURE:

  1. Dry vacuum area thoroughly to remove as much excess contamination as possible (this is very important).
  2. Apply dilute solution (15:1) Power Gel to contaminated fibers.
  3. Using Carpet Shark, agitate treated area until contamination becomes suspended in foam.
  4. Dry extract (no water) foam.
  5. Repeat steps 2 through 4 until foam no longer colors from substance.
  6. Thoroughly hot water extraction rinse area to remove Power Gel solution.
  7. If light color residue remains apply Stain Magic and allow dwell time. Stain will disappear as it dries.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Power Gel and Last Step Rinse.

PROCEDURE:

  1. Scrape away excess contamination.
  2. Apply Power Gel liberally to spot.
  3. Agitate gently but thoroughly to emulsify compound.
  4. Rinse clean using a dilute solution of Last Step Rinse.

 

Tip: Solvents are not as effective as Power Gel on this substance.

TOOLS REQUIRED: HWE and Carpet Shark.

CHEMICALS REQUIRED: Stain Magic and Power Gel.

PROCEDURE:

  1. Pre spray stained area with a dilute solution (20:1) of Power Gel.
  2. Agitate gently but thoroughly to emulsify contamination.
  3. Hot water extraction rinse spot, and leave carpet as dry as possible by blotting with a dry towel.
  4. If stain remains, apply Stain Magic to the discolored fibers with trigger sprayer and gently agitate.

 

Tip: Stain will disappear in 1 to 8 hours depending on severity. To speed stain removal, use the Pro’s Choice DCI Light with the Chemical Activation Bulb.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel.

CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.

 

Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).

 

Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.

 

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel.

CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.

 

Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).

 

Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.

 

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIREDHWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark.

CHEMICALS REQUIRED: Pro Solve Gel.

PROCEDURE:

  1.  Apply Pro Solve Gel to deposit.
  2.  Agitate gently until crayon dissolves into gel.
  3.  Hot water extraction rinse area.

TOOLS REQUIREDHWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE, Pro’s Choice DCI Light.

CHEMICALS REQUIRED: Stain Magic and Power Gel.

 

Suggestions and Cautions:

This is considered a dispersed dye and is one of the most difficult stains you will encounter, however if you have the Pro’s Choice DCI Light you can achieve miraculous results.

 

If you do not have a DCI Light you can use a secondary procedure with a steam iron but be advised it is possible to cause the Stain Magic to over-react and pull color from the carpet.  The DCI Light is REALLY the safest and most effective way to remove these stains.

 

It is MOST important NOT to apply heat either from high temperature cleaning or from stain removal procedures other than the procedure, which follows:

The performance of this procedure will vary depending on three things:

  1. What previous treatments have been made to the stain.
  2. The age of the stain.
  3. Your treatment technique.

 

PROCEDURE:

Using DCI Light:

  1. Apply Power Gel to contamination and agitate.
  2. Thoroughly extraction rinse stain to remove all staining material and detergents.
  3. Blot the stain dry with absorbent towel.
  4. Saturate stain with Stain Magic solution.
  5. Cover stain with DCI Chemical Activation Light.
  6. Allow lamp to dwell until stain disappears. This time will vary from 30 minutes to 6 hours depending on severity of stain.

 

No DCI Light:

  1. Apply Power Gel to contamination and agitate.
  2. Thoroughly extraction rinse stain to remove all staining material and detergents.
  3. Blot the stain dry with absorbent towel.
  4. Saturate stain with Stain Magic solution.
  5. Cover the area with a damp towel folded in half.
  6. Using a steam iron set on the lowest “steam” setting and actively producing steam apply heat in 10 second increments (up to 3 applications). If color loss or fiber distortion is observed discontinue immediately and advise customer that remaining stain is permanent.

TOOLS REQUIRED: HWE, Trigger Sprayer and Carpet Shark.

CHEMICALS REQUIRED: Power Gel and Stain Magic.

PROCEDURE:

  1. Dry vacuum area thoroughly to remove as much excess contamination as possible (this is very important).
  2. Apply dilute solution (15:1) Power Gel to contaminated fibers.
  3. Using Carpet Shark, agitate treated area until contamination becomes suspended in foam.
  4. Dry extract (no water) foam.
  5. Repeat steps 2 through 4 until foam no longer colors from substance.
  6. Thoroughly hot water extraction rinse area to remove Power Gel solution.
  7. If light color residue remains apply Stain Magic and allow dwell time. Stain will disappear as it dries.

TOOLS REQUIRED: HWE and Carpet Shark.

CHEMICALS REQUIRED: Stain Magic and Power Gel.

PROCEDURE:

  1. Pre spray stained area with a dilute solution (20:1) of Power Gel.
  2. Agitate gently but thoroughly to emulsify contamination.
  3. Hot water extraction rinse spot, and leave carpet as dry as possible by blotting with a dry towel.
  4. If stain remains, apply Stain Magic to the discolored fibers with trigger sprayer and gently agitate.

 

Tip: Stain will disappear in 1 to 8 hours depending on severity. To speed stain removal, use the Pro’s Choice DCI Light with the Chemical Activation Bulb.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel.

CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.

 

Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).

 

Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.

 

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel.

CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.

 

Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).

 

Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.

 

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel.

CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.

 

Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).

 

Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.

 

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Power Gel and Last Step Rinse.

PROCEDURE:

  1. Scrape away excess contamination.
  2. Apply Power Gel liberally to spot.
  3. Agitate gently but thoroughly to emulsify compound.
  4. Rinse clean using a dilute solution of Last Step Rinse.

 

Tip: Solvents are not as effective as Power Gel on this substance.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark.

CHEMICALS REQUIRED: PC-45 and Urine Stain Remover.

PROCEDURE:

  1. Apply PC-45 to stained fibers.
  2. Agitate the treated areas gently but thoroughly.
  3. Hot water extraction rinse with clear hot water or extraction emulsifier.
  4. If a visible discoloration remains that resists treatment apply Urine Stain Remover in a trigger or pump sprayer.
TOOLS REQUIRED: HWE and Carpet Shark. CHEMICALS REQUIRED: Pro Solve Gel and Stain Magic.

PROCEDURE:

  1. Apply Pro Solve Gel to deposit.
  2. Agitate gently to work gel into deposit.
  3. Apply more Pro Solve Gel to cover deposit.
  4. Allow 5-minute dwell time.
  5. Agitate gently to fully dissolve and suspend deposit.
  6. Hot water extraction rinse.
  7. Thoroughly blot dry.
  8. If a visible stain still exists, apply a solution of Stain Magic to stained fibers only.
  9. Cover with lightweight terry cloth towel.
  10. Apply steam heat from steam iron set at low steam setting (approximately mid range) in 15-second intervals.
  11. Check progress periodically by peeking under towel.
  12. Remove heat when stain is gone or if any carpet color loss is observed.
  Note: Nail polish must be completely removed before stain removal procedures will work.

TOOLS REQUIRED: HWE, Trigger Sprayer and Carpet Shark.

CHEMICALS REQUIRED: Power Gel and Stain Magic.

PROCEDURE:

  1. Dry vacuum area thoroughly to remove as much excess contamination as possible (this is very important).
  2. Apply dilute solution (15:1) Power Gel to contaminated fibers.
  3. Using Carpet Shark, agitate treated area until contamination becomes suspended in foam.
  4. Dry extract (no water) foam.
  5. Repeat steps 2 through 4 until foam no longer colors from substance.
  6. Thoroughly hot water extraction rinse area to remove Power Gel solution.
  7. If light color residue remains apply Stain Magic and allow dwell time. Stain will disappear as it dries.

TOOLS REQUIRED: HWE and Carpet Shark.

CHEMICALS REQUIRED: Stain Magic and Power Gel.

PROCEDURE:

  1. Pre spray stained area with a dilute solution (20:1) of Power Gel.
  2. Agitate gently but thoroughly to emulsify contamination.
  3. Hot water extraction rinse spot, and leave carpet as dry as possible by blotting with a dry towel.
  4. If stain remains, apply Stain Magic to the discolored fibers with trigger sprayer and gently agitate.

Tip: Stain will disappear in 1 to 8 hours depending on severity. To speed stain removal, use the Pro’s Choice DCI Light with the Chemical Activation Bulb.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel.

CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.

 

Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).

 

Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.

 

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel.

CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.

 

Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).

 

Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.

 

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE, Carpet Shark and Plastic Sheet.

CHEMICALS REQUIRED: Stain Magic, Rust Away and Pro Solve Gel.

PROCEDURE:

Furniture stains are normally caused by one of the following:

  1. Rust from metal leg supports.
  2. Tannin color leaching from wood.
  3. Dye from the furniture finish.

 

Tip: You will be able to remove stains caused by rust and tannin but you will not always be successful in removing stains caused by dye in the finish on the furniture.

 

Caution: When testing for rust test on a small area only as rust remover may set tannin and dye stains.

 

Furniture Stains:

  1. Clean spot with Pro Solve Gel to remove oil base contamination.
  2. Thoroughly extraction rinse and blot dry.
  3. Proceed with the following stain removal procedures depending on the source of the stain.

A. Rust.

  1. If stain is determined to be rust, apply Rust Away.
  2. Agitate gently until stain disappears.
  3. Hot water extraction rinse.

B. Tannin Stain.

  1. If stain is determined to be from wood, apply Stain Magic to stained fibers.
  2. Lightly cover with clear plastic sheet such as sandwich wrap and allow 12 hours dwell time.
  3. Severe stains may require more than one treatment.  If stain is not completely removed, mix fresh solution of Stain Magic and repeat process.

C. Dye from furniture finish.

  1. Apply Stain Magic, cover with DCI Light and allow 8 hours dwell time.

TOOLS REQUIRED: HWE

CHEMICALS REQUIRED: Extreme Clean, Energy and X-Cide.

PROCEDURE:

  1. Mix Extreme Clean and Energy according to directions.
  2. Saturate contaminated area and use wand as a squeegee to emulsify contamination.
  3. Dry extract area to remove as much of the contamination.
  4. Repeat steps 2-3 until contamination has been removed.
  5. Saturate area with clear water and dry extract to remove residue.
  6. Treat area with X-Cide to eliminate any residual odors from fuel.

TOOLS REQUIRED: HWE and Carpet Shark.

CHEMICALS REQUIRED: Stain Magic and Power Gel.

PROCEDURE:

  1. Pre spray stained area with a dilute solution (20:1) of Power Gel.
  2. Agitate gently but thoroughly to emulsify contamination.
  3. Hot water extraction rinse spot, and leave carpet as dry as possible by blotting with a dry towel.
  4. If stain remains, apply Stain Magic to the discolored fibers with trigger sprayer and gently agitate.

Tip: Stain will disappear in 1 to 8 hours depending on severity. To speed stain removal, use the Pro’s Choice DCI Light with the Chemical Activation Bulb.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel. CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.
  Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).   Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.  

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel. CHEMICALS REQUIRED: Red Relief PROCEDURE: Clean stained area using hot water extraction. Blot area dry with clean white towel to remove excess moisture from carpet. Mix Red Relief Part A and Part B in equal parts. Using trigger sprayer, wet stained fibers with Red Relief mixture. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here. Apply steam heat from an iron set at the lowest steam temperature. Check the stain every 30 seconds. When the stain has turned to a light yellow or has disappeared, remove heat and towel. Extraction rinse chemical residue away. Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important). Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight. The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Power Gel and Last Step Rinse.

PROCEDURE:

  1. Scrape away excess contamination.
  2. Apply Power Gel liberally to spot.
  3. Agitate gently but thoroughly to emulsify compound.
  4. Rinse clean using a dilute solution of Last Step Rinse.

 

Tip: Solvents are not as effective as Power Gel on this substance.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE, Trigger Sprayer and Carpet Shark.

CHEMICALS REQUIRED: Power Gel and Stain Magic.

PROCEDURE:

  1. Dry vacuum area thoroughly to remove as much excess contamination as possible (this is very important).
  2. Apply dilute solution (15:1) Power Gel to contaminated fibers.
  3. Using Carpet Shark, agitate treated area until contamination becomes suspended in foam.
  4. Dry extract (no water) foam.
  5. Repeat steps 2 through 4 until foam no longer colors from substance.
  6. Thoroughly hot water extraction rinse area to remove Power Gel solution.
  7. If light color residue remains apply Stain Magic and allow dwell time. Stain will disappear as it dries.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIREDHWE and Carpet Shark

CHEMICALS REQUIRED: Citra Quick (Solvent) and Power Gel.

PROCEDURE:

  1. Apply Citra Quick to grease deposit.
  2. Agitate gently to dissolve soil.
  3. Apply Power Gel and agitate to emulsify and suspend soil.
  4. Hot water extraction rinse.
TOOLS REQUIRED: HWE and Carpet Shark CHEMICALS REQUIRED: Amazing GOOFF (solvent), Power Gel and ARA.

PROCEDURE:

  1. Use the Carpet Shark to perforate the gum deposit and allow the solvent to penetrate the interior of the deposit.
  2. Apply the GOOFF to the gum deposit.
  3. Allow dwell time.  Up to 2 minutes.
  4. Scrape gum and GOOFF residue from carpet fibers.
  5. Apply Power Gel to the area and agitate to emulsify any residues.
  6. Extraction rinse area.
  7. Apply ARA to the area to prevent any residues from attracting soil.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Power Gel and Red Relief.

 

PROCEDURE:

Generally you will find this type of stain to be removable from stain resistant nylons and olefins. You will find it to be more difficult, if not impossible, to remove from wool.

  1. Apply Power Gel to stain.
  2. Agitate gently but thoroughly to emulsify the spot as much as possible.
  3. Thoroughly rinse clean via hot water extraction. Leave as dry as possible by making multiple (vacuum only) drying strokes.
  4. If visible stain remains mix Red Relief Part A and Part B in equal parts (or use Red 1).
  5. Using trigger sprayer, wet stained fibers with Red 1 or Red Relief mixture. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared remove heat and towel.
  9. Extraction rinse chemical residue away.
  10. If discoloration persists following the Red Relief treatment the stain is permanent.

Tip: DO NOT apply an oxidizing agent such as Hydrogen Peroxide or a high P.H. enzyme to hair dye stains. It will only intensify them.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark.

CHEMICALS REQUIRED: Stain Magic and Power Gel.

PROCEDURE:

  1. Pre spray stained area with a dilute solution (20:1) of Power Gel.
  2. Agitate gently but thoroughly to emulsify contamination.
  3. Hot water extraction rinse spot, and leave carpet as dry as possible by blotting with a dry towel.
  4. If stain remains, apply Stain Magic to the discolored fibers with trigger sprayer and gently agitate.

Tip: Stain will disappear in 1 to 8 hours depending on severity. To speed stain removal, use the Pro’s Choice DCI Light with the Chemical Activation Bulb.

TOOLS REQUIRED: HWE, Carpet Shark and trigger sprayer

CHEMICALS REQUIRED: Red Relief or Red 1.

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Stain should disappear within 15 minutes.
  6. Extraction rinse chemical residue away.

TOOLS REQUIRED: HWE and Carpet Shark.

CHEMICALS REQUIRED: Stain Magic and Power Gel.

PROCEDURE:

  1. Pre spray stained area with a dilute solution (20:1) of Power Gel.
  2. Agitate gently but thoroughly to emulsify contamination.
  3. Hot water extraction rinse spot, and leave carpet as dry as possible by blotting with a dry towel.
  4. If stain remains, apply Stain Magic to the discolored fibers with trigger sprayer and gently agitate.

Tip: Stain will disappear in 1 to 8 hours depending on severity. To speed stain removal, use the Pro’s Choice DCI Light with the Chemical Activation Bulb.

TOOLS REQUIRED: HWE, Carpet Shark and trigger sprayer

CHEMICALS REQUIRED: Red Relief or Red 1.

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Stain should disappear within 15 minutes.
  6. Extraction rinse chemical residue away.

 

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOL REQUIRED: HWE, Carpet Shark and possibly steam iron. CHEMICALS REQUIRED: Stain Magic, Pro Solve Liquid.

PROCEDURE:

  1. Apply Stain Magic liberally to ink stain and areas 1 inch around stain.
  2. Apply Pro-Solve Liquid to the stained fibers.
  3. Agitate gently but thoroughly with a Carpet Shark or bone scraper until ink has dissolved.
  4. Re-apply Stain Magic.
  5. Thoroughly hot water extraction rinse.
  6. Repeat as necessary.
  Tip: If color from the stain remains apply Stain Magic, cover with damp towel and steam heat for 15 seconds, checking the stain every 3 seconds.

TOOLS REQUIRED: HWE, Carpet Shark and trigger sprayer.

CHEMICALS REQUIRED: Stain Magic and Power Gel.

PROCEDURE:

  1. Pre spray stained area with a dilute solution (20:1) of Power Gel.
  2. Agitate gently but thoroughly to emulsify contamination.
  3. Hot water extraction rinse spot, and leave carpet as dry as possible by blotting with a dry towel.

 

Tip: If stain remains apply Stain Magic, cover with damp towel and steam heat for 15 seconds.

TOOLS REQUIRED: HWE, Carpet Shark and trigger sprayer.

CHEMICALS REQUIRED: Stain Magic and Power Gel.

PROCEDURE:

  1. Pre spray stained area with a dilute solution (20:1) of Power Gel.
  2. Agitate gently but thoroughly to emulsify contamination.
  3. Hot water extraction rinse spot, and leave carpet as dry as possible by blotting with a dry towel.

 

Tip: If stain remains apply Stain Magic, cover with damp towel and steam heat for 15 seconds.

TOOLS REQUIRED: HWE, Carpet Shark and trigger sprayer.

CHEMICALS REQUIRED: Stain Magic and Power Gel.

PROCEDURE:

  1. Pre spray stained area with a dilute solution (20:1) of Power Gel.
  2. Agitate gently but thoroughly to emulsify contamination.
  3. Hot water extraction rinse spot, and leave carpet as dry as possible by blotting with a dry towel.

 

Tip: If stain remains apply Stain Magic, cover with damp towel and steam heat for 15 seconds.

 

TOOLS REQUIRED: HWE, Carpet Shark and trigger sprayer.

CHEMICALS REQUIRED: Stain Magic and Power Gel.

PROCEDURE:

  1. Pre spray stained area with a dilute solution (20:1) of Power Gel.
  2. Agitate gently but thoroughly to emulsify contamination.
  3. Hot water extraction rinse spot, and leave carpet as dry as possible by blotting with a dry towel.

 

Tip: If stain remains apply Stain Magic, cover with damp towel and steam heat for 15 seconds.

 

TOOL REQUIRED: HWE, Carpet Shark and possibly steam iron.

CHEMICALS REQUIRED: Stain Magic, Ink Out, Pro Solve Gel, and Power Gel.

PROCEDURE:

FOR UPHOLSTERY:

  1. Apply Stain Magic liberally to ink stain and areas 1 inch around stain.
  2. Apply Ink Out to ink. This will remove stain color.
  3. Agitate gently but thoroughly with a Carpet Shark or bone scraper until ink has dissolved.
  4. Re-apply Stain Magic.
  5. Thoroughly hot water extraction rinse.

 

IF ONLY STAIN COLOR REMAINS (synthetic fibers only):

  1. Re-apply Stain Magic Solution.
  2. Cover with damp towel.
  3. Heat with steaming iron for 15 seconds.

 

FOR CARPET:

  1. Apply Pro Solve to ink deposit.
  2. Agitate gently but thoroughly until deposit is dissolved.
  3. Apply Power Gel to deposit and agitate.
  4. Thoroughly hot water extraction rinse.

 

Tip: If stain remains apply Stain Magic, cover with damp towel and steam heat for 15 seconds.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel. CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.
  Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).   Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.  

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Power Gel

 

PROCEDURE:

  1. Apply a dilute solution (20:1) of Power Gel to spot.
  2. Gently but thoroughly agitate spot until compound is emulsified.
  3. Thoroughly rinse spot from fibers using hot water extraction.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark.

CHEMICALS REQUIRED: Stain Magic and Power Gel.

PROCEDURE:

  1. Pre spray stained area with a dilute solution (20:1) of Power Gel.
  2. Agitate gently but thoroughly to emulsify contamination.
  3. Hot water extraction rinse spot, and leave carpet as dry as possible by blotting with a dry towel.
  4. If stain remains, apply Stain Magic to the discolored fibers with trigger sprayer and gently agitate.

Tip: Stain will disappear in 1 to 8 hours depending on severity. To speed stain removal, use the Pro’s Choice DCI Light with the Chemical Activation Bulb.

 

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel.

CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.

 

Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).

 

Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.

 

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel.

CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.

 

Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).

 

Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.

 

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel.

CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.

 

Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).

 

Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.

 

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Sprayer

CHEMICALS REQUIRED: Last Step, Crystal Foam Kill, and ARA.

PROCEDURE:

  1. Saturate area thoroughly with a dilute solution of Last Step to solubilize the dried contamination.
  2. Gently but thoroughly agitate fibers to break up and emulsify deposit.
  3. Flush contamination away from fibers (for deep spills that have penetrated the backing and pad under the carpet repeated saturation treatments followed by extraction with a sub-surface extraction device may be necessary).
  4. Use Foam Kill as necessary to prevent foam build-up in recovery tank.
  5. Apply ARA to the area and groom into the fibers and allow to dry completely.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Power Gel and Last Step Rinse.

PROCEDURE:

  1. Scrape away excess contamination.
  2. Apply Power Gel liberally to spot.
  3. Agitate gently but thoroughly to emulsify compound.
  4. Rinse clean using a dilute solution of Last Step Rinse.

 

Tip: Solvents are not as effective as Power Gel on this substance.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIREDHWE and Carpet Shark CHEMICALS REQUIRED: Power Gel and Last Step Rinse.

PROCEDURE:

  1. Scrape away excess contamination.
  2. Apply Power Gel liberally to spot.
  3. Agitate gently but thoroughly to emulsify compound.
  4. Rinse clean using a dilute solution of Last Step Rinse.
  Tip: Solvents are not as effective as Power Gel on this substance.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and a hand brush or Carpet Shark.

CHEMICALS REQUIRED: Power Gel and Stain Magic (Oxidizer).

PROCEDURE:

  1. Apply a dilute solution (20:1) of Power Gel to the spot.
  2. Agitate gently but thoroughly.
  3. Hot water extraction clean. Leave as dry as possible using multiple vacuum only wand strokes and blot dry with towel.
  4. Apply Stain Magic evenly with trigger sprayer.
  5. Agitate gently.
  6. Allow to dry completely.
  7. Tip: The stain will fade away as it reacts with the Stain Magic. Reaction time will vary from 15 minutes to 5 hours.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and a hand brush or Carpet Shark.

CHEMICALS REQUIRED: Power Gel and Stain Magic (Oxidizer).

PROCEDURE:

  1. Apply a dilute solution (20:1) of Power Gel to the spot.
  2. Agitate gently but thoroughly.
  3. Hot water extraction clean. Leave as dry as possible using multiple vacuum only wand strokes and blot dry with towel.
  4. Apply Stain Magic evenly with trigger sprayer.
  5. Agitate gently.
  6. Allow to dry completely.
  7. Tip: The stain will fade away as it reacts with the Stain Magic. Reaction time will vary from 15 minutes to 5 hours.
TOOLS REQUIRED: HWE, Pro’s Choice DCI Light. CHEMICALS REQUIRED: Stain Magic and Power Gel.

Suggestions and Cautions:

This is considered a dispersed dye and is one of the most difficult stains you will encounter, however if you have the Pro’s Choice DCI Light you can achieve miraculous results.   If you do not have a DCI Light you can use a secondary procedure with a steam iron but be advised it is possible to cause the Stain Magic to over-react and pull color from the carpet.  The DCI Light is REALLY the safest and most effective way to remove these stains.   It is MOST important NOT to apply heat either from high temperature cleaning or from stain removal procedures other than the procedure, which follows: The performance of this procedure will vary depending on three things:
  1. What previous treatments have been made to the stain.
  2. The age of the stain.
  3. Your treatment technique.
 

PROCEDURE:

Using DCI Light:

  1. Apply Power Gel to contamination and agitate.
  2. Thoroughly extraction rinse stain to remove all staining material and detergents.
  3. Blot the stain dry with absorbent towel.
  4. Saturate stain with Stain Magic solution.
  5. Cover stain with DCI Chemical Activation Light.
  6. Allow lamp to dwell until stain disappears. This time will vary from 30 minutes to 6 hours depending on severity of stain.
 

No DCI Light:

  1. Apply Power Gel to contamination and agitate.
  2. Thoroughly extraction rinse stain to remove all staining material and detergents.
  3. Blot the stain dry with absorbent towel.
  4. Saturate stain with Stain Magic solution.
  5. Cover the area with a damp towel folded in half.
  6. Using a steam iron set on the lowest “steam” setting and actively producing steam apply heat in 10 second increments (up to 3 applications). If color loss or fiber distortion is observed discontinue immediately and advise customer that remaining stain is permanent.

Not all stains are easily identified and this guide is by no means a complete reference.  If you have additional questions contact technical support at (800) 368-1247.

 

  1. Apply Pro Solve gel.  If Stain responds, agitate until stain is dissolved.  Apply Power Gel and agitate to emulsify deposit and extract.
  2. If stain does not respond, extract and blot area dry.  Apply Power Gel and agitate.  If stain responds, agitate to break down and emulsify stain then extract to remove suspended contamination.
  3. If stain does not respond, extract and blot area dry.  Observe the staining material.  If stain appears to be more brilliant, apply Red Relief or Red 1 according to the directions.  If the stain appears to be muted or dull, apply a solution of Stain Magic or Stain 1 and allow to dry.

 

TOOLS REQUIRED: HWE and a hand brush or Carpet Shark.

CHEMICALS REQUIRED: Power Gel and Stain Magic (Oxidizer).

PROCEDURE:

  1. Apply a dilute solution (20:1) of Power Gel to the spot.
  2. Agitate gently but thoroughly.
  3. Hot water extraction clean. Leave as dry as possible using multiple vacuum only wand strokes and blot dry with towel.
  4. Apply Stain Magic evenly with trigger sprayer.
  5. Agitate gently.
  6. Allow to dry completely.
  7. Tip: The stain will fade away as it reacts with the Stain Magic. Reaction time will vary from 15 minutes to 5 hours.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE, Carpet Shark, steam iron, and lightweight terry cloth towel. CHEMICALS REQUIRED: Pro Solve Gel, Power Gel and Last Step Textile Rinse.   PROCEDURE (If paint is still wet):
  1. Apply Pro Solve Gel liberally to spot.
  2. Gently but thoroughly agitate spot with Carpet Shark to dissolve paint.
  3. Apply Power Gel and agitate gently but thoroughly to emulsify contamination.
  4. Thoroughly extract using hot water extraction.
  5. Repeat steps 1 through 3 as required.
  6. Rinse carpet using dilute solution of Last Step Rinse.
  PROCEDURE (If paint is dry):
  1. Apply Pro Solve Gel to wet fibers.
  2. Agitate gently but thoroughly with Carpet Shark.
  3. Cover with clean terry cloth towel.
  4. Apply steam heat from steam iron set at mid range temperature for 30 seconds.
  5. Re-apply Pro Solve Gel.
  6. Agitate gently, but thoroughly.
  7. Apply Power Gel liberally to spot.
  8. Gently, but thoroughly, agitate to emulsify dissolved paint.
  9. Thoroughly extract using hot water extraction.
  10. Repeat steps 7 through 9 if necessary.
  11. Rinse thoroughly using a dilute solution of Last Step Rinse.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Power Gel and Last Step Rinse.

PROCEDURE:

  1. Scrape away excess contamination.
  2. Apply Power Gel liberally to spot.
  3. Agitate gently but thoroughly to emulsify compound.
  4. Rinse clean using a dilute solution of Last Step Rinse.

 

Tip: Solvents are not as effective as Power Gel on this substance.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIREDHWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Solve Gel (solvent), Power Gel and ARA.

PROCEDURE:

  1. Use the Carpet Shark to perforate the deposit and allow the solvent to penetrate the interior of the deposit.
  2. Apply the Pro-Solve to the deposit.
  3. Allow dwell time.  Up to 2 minutes.
  4. Scrape deposit and Pro-Solve residue from carpet fibers.
  5. Apply Power Gel to the area and agitate to emulsify any residues.
  6. Extraction rinse area.
  7. Apply ARA to the area to prevent any residues from attracting soil.

 

TOOLS REQUIRED: HWE and Carpet Shark.

CHEMICALS REQUIRED: Stain Magic and Power Gel.

PROCEDURE:

  1. Pre spray stained area with a dilute solution (20:1) of Power Gel.
  2. Agitate gently but thoroughly to emulsify contamination.
  3. Hot water extraction rinse spot, and leave carpet as dry as possible by blotting with a dry towel.
  4. If stain remains, apply Stain Magic to the discolored fibers with trigger sprayer and gently agitate.

Tip: Stain will disappear in 1 to 8 hours depending on severity. To speed stain removal, use the Pro’s Choice DCI Light with the Chemical Activation Bulb.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel.

CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.

 

Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).

 

Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.

 

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel.

CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.

 

Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).

 

Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.

 

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIREDHWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Solve Gel (solvent), Power Gel and ARA.

 

PROCEDURE:

  1. Use the Carpet Shark to perforate the deposit and allow the solvent to penetrate the interior of the deposit.
  2. Apply the Pro-Solve to the deposit.
  3. Allow dwell time.  Up to 2 minutes.
  4. Scrape deposit and Pro-Solve residue from carpet fibers.
  5. Apply Power Gel to the area and agitate to emulsify any residues.
  6. Extraction rinse area.
  7. Apply ARA to the area to prevent any residues from attracting soil.
TOOLS REQUIRED: HWE and Carpet Shark CHEMICALS REQUIRED: Rust Away  

PROCEDURE:

Rust is one of the worst appearing yet easy to remove stains.
  1. Apply Rust Away to the stained fibers.
  2. Agitate gently and watch the stain disappear.
  3. Rinse with hot water extraction cleaning.
  Tip: Rust Away is very effective. You will probably see the rust disappear before you have a chance to agitate the fibers.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Sprayer

CHEMICALS REQUIRED: Last Step, Crystal Foam Kill, and ARA.

PROCEDURE:

  1. Saturate area thoroughly with a dilute solution of Last Step to solubilize the dried contamination.
  2. Gently but thoroughly agitate fibers to break up and emulsify deposit.
  3. Flush contamination away from fibers (for deep spills that have penetrated the backing and pad under the carpet repeated saturation treatments followed by extraction with a sub-surface extraction device may be necessary).
  4. Use Foam Kill as necessary to prevent foam build-up in recovery tank.
  5. Apply ARA to the area and groom into the fibers and allow to dry completely.

 

TOOLS REQUIRED: HWE, Trigger Sprayer and Carpet Shark. CHEMICALS REQUIRED: Power Gel and Stain Magic. PROCEDURE:
  1. Apply dilute solution (15:1) Power Gel to contaminated fibers.
  2. Using Carpet Shark, agitate treated area until contamination becomes suspended in foam.
  3. Extract area thoroughly.
  4. Repeat steps 1 through 3 until foam no longer colors from substance.
  5. Thoroughly hot water extraction rinse area to remove Power Gel solution.
  6. If light color residue remains apply Stain Magic and allow dwell time. Stain will disappear as it dries.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Power Gel, Pro Solve and Last Step

To successfully remove silicone sealant you must begin your procedure before the deposit dries to a solid! Once dry, silicone cannot be removed chemically without carpet damage.

PROCEDURE:

  1. Scrape away excess contamination.
  2. Apply Power Gel liberally to spot.
  3. Gently but thoroughly agitate spot to emulsify deposit.
  4. Rinse thoroughly using hot water extraction.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Solve Gel (solvent), Power Gel and ARA.

 

PROCEDURE:

  1. Use the Carpet Shark to perforate the deposit and allow the solvent to penetrate the interior of the deposit.
  2. Apply the Pro-Solve to the deposit.
  3. Allow dwell time.  Up to 2 minutes.
  4. Scrape deposit and Pro-Solve residue from carpet fibers.
  5. Apply Power Gel to the area and agitate to emulsify any residues.
  6. Extraction rinse area.
  7. Apply ARA to the area to prevent any residues from attracting soil.

TOOLS REQUIRED: HWE and Sprayer

CHEMICALS REQUIRED: Last Step, Crystal Foam Kill, and ARA.

PROCEDURE:

  1. Saturate area thoroughly with a dilute solution of Last Step to solubilize the dried contamination.
  2. Gently but thoroughly agitate fibers to break up and emulsify deposit.
  3. Flush contamination away from fibers (for deep spills that have penetrated the backing and pad under the carpet repeated saturation treatments followed by extraction with a sub-surface extraction device may be necessary).
  4. Use Foam Kill as necessary to prevent foam build-up in recovery tank.
  5. Apply ARA to the area and groom into the fibers and allow to dry completely.

TOOLS REQUIRED: HWE and Sprayer

CHEMICALS REQUIRED: Power Gel and Stain 1

PROCEDURE:

  1. Apply dilute solution of Power Gel to stained fibers.
  2. Gently but thoroughly agitate to break up and emulsify deposit.
  3. Flush contamination away from fibers (for deep spills that have penetrated the backing and pad under the carpet repeated saturation treatments followed by extraction with a sub-surface extraction device may be necessary).
  4. If visible discoloration remains after substance has been removed apply Stain 1 to the area and allow to dry completely.

TOOLS REQUIREDHWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel.

CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.

 

Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).

 

Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.

 

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE, Carpet Shark, trigger sprayer, steam iron and a terrycloth towel.

CHEMICALS REQUIRED: Red Relief

PROCEDURE:

  1. Clean stained area using hot water extraction.
  2. Blot area dry with clean white towel to remove excess moisture from carpet.
  3. Mix Red Relief Part A and Part B in equal parts.
  4. Using trigger sprayer, wet stained fibers with Red Relief mixture.
  5. Cover spot with a moderately wet (excess water squeezed out) terry towel. Note: A lightweight-cleaning towel folded double works well here.
  6. Apply steam heat from an iron set at the lowest steam temperature.
  7. Check the stain every 30 seconds.
  8. When the stain has turned to a light yellow or has disappeared, remove heat and towel.
  9. Extraction rinse chemical residue away.

 

Tips: Usually incomplete stain removal is the result of insufficient heating time (high temperature is not necessary but dwell time is important).

 

Red Relief will continue to work on stains which have penetrated dye sites even after you have rinsed the carpet clean. Because of this, you will find that if the slightest tinge of red remains following your treatment, it will disappear overnight.

 

The type of iron you use is IMPORTANT, here’s why… Conventional irons can work against you because of uneven heat/steam application to the carpet. The iron that will serve you best is an iron which has steam vents covering the ironing surface rather than one with with a single row of vents around the perimeter of the ironing surface.

TOOLS REQUIRED: HWE, Trigger Sprayer and Carpet Shark.

CHEMICALS REQUIRED: Power Gel and Stain Magic.

PROCEDURE:

  1. Dry vacuum area thoroughly to remove as much excess contamination as possible (this is very important).
  2. Apply dilute solution (15:1) Power Gel to contaminated fibers.
  3. Using Carpet Shark, agitate treated area until contamination becomes suspended in foam.
  4. Dry extract (no water) foam.
  5. Repeat steps 2 through 4 until foam no longer colors from substance.
  6. Thoroughly hot water extraction rinse area to remove Power Gel solution.
  7. If light color residue remains apply Stain Magic and allow dwell time. Stain will disappear as it dries.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

 

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and ARA Anti Re-Soiling Agent

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. If a visible discoloration remains apply Stain Magic to the area, agitate gently to aid in penetration and allow to dry.

 

SUGGESTIONS AND CAUTIONS:

Sticky substances like Syrup may leave a residue that will attract soil  Use ARA as a finishing touch to crystallize any sticky residues.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Amazing GOOFF (solvent), Power Gel and ARA.

PROCEDURE:

  1. Use the Carpet Shark to perforate the deposit and allow the solvent to penetrate the interior of the deposit.
  2. Apply the GOOFF to the deposit.
  3. Allow dwell time.  Up to 2 minutes.
  4. Scrape deposit and GOOFF residue from carpet fibers.
  5. Apply Power Gel to the area and agitate to emulsify any residues.
  6. Extraction rinse area.
  7. Apply ARA to the area to prevent any residues from attracting soil.

 

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIREDHWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE, Pro’s Choice DCI Light. CHEMICALS REQUIRED: Stain Magic and Power Gel.

Suggestions and Cautions:

This is considered a dispersed dye and is one of the most difficult stains you will encounter, however if you have the Pro’s Choice DCI Light you can achieve miraculous results.   If you do not have a DCI Light you can use a secondary procedure with a steam iron but be advised it is possible to cause the Stain Magic to over-react and pull color from the carpet.  The DCI Light is REALLY the safest and most effective way to remove these stains.   It is MOST important NOT to apply heat either from high temperature cleaning or from stain removal procedures other than the procedure, which follows: The performance of this procedure will vary depending on three things:
  1. What previous treatments have been made to the stain.
  2. The age of the stain.
  3. Your treatment technique.
 

PROCEDURE:

Using DCI Light:

  1. Apply Power Gel to contamination and agitate.
  2. Thoroughly extraction rinse stain to remove all staining material and detergents.
  3. Blot the stain dry with absorbent towel.
  4. Saturate stain with Stain Magic solution.
  5. Cover stain with DCI Chemical Activation Light.
  6. Allow lamp to dwell until stain disappears. This time will vary from 30 minutes to 6 hours depending on severity of stain.
 

No DCI Light:

  1. Apply Power Gel to contamination and agitate.
  2. Thoroughly extraction rinse stain to remove all staining material and detergents.
  3. Blot the stain dry with absorbent towel.
  4. Saturate stain with Stain Magic solution.
  5. Cover the area with a damp towel folded in half.
  6. Using a steam iron set on the lowest “steam” setting and actively producing steam apply heat in 10 second increments (up to 3 applications). If color loss or fiber distortion is observed discontinue immediately and advise customer that remaining stain is permanent.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIREDHWE, Carpet Shark and Plastic Sheet.

CHEMICALS REQUIRED: Stain Magic, Rust Away and Pro Solve Gel.

PROCEDURE:

Furniture stains are normally caused by one of the following:

  1. Rust from metal leg supports.
  2. Tannin color leaching from wood.
  3. Dye from the furniture finish.

 

Tip: You will be able to remove stains caused by rust and tannin but you will not always be successful in removing stains caused by dye in the finish on the furniture.

 

Caution: When testing for rust test on a small area only as rust remover may set tannin and dye stains.

 

Furniture Stains:

  1. Clean spot with Pro Solve Gel to remove oil base contamination.
  2. Thoroughly extraction rinse and blot dry.
  3. Proceed with the following stain removal procedures depending on the source of the stain.

A. Rust.

  1. If stain is determined to be rust, apply Rust Away.
  2. Agitate gently until stain disappears.
  3. Hot water extraction rinse.

B. Tannin Stain.

  1. If stain is determined to be from wood, apply Stain Magic to stained fibers.
  2. Lightly cover with clear plastic sheet such as sandwich wrap and allow 12 hours dwell time.
  3. Severe stains may require more than one treatment.  If stain is not completely removed, mix fresh solution of Stain Magic and repeat process.

C. Dye from furniture finish.

  1. Apply Stain Magic, cover with DCI Light and allow 8 hours dwell time.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Power Gel and Last Step Rinse.

PROCEDURE:

  1. Scrape away excess contamination.
  2. Apply Power Gel liberally to spot.
  3. Agitate gently but thoroughly to emulsify compound.
  4. Rinse clean using a dilute solution of Last Step Rinse.

 

Tip: Solvents are not as effective as Power Gel on this substance.

TOOLS REQUIRED: HWE, Carpet Shark. and Pro’s Choice DCI Light.

CHEMICALS REQUIRED: Stain Magic and Dry Citric Acid.

PROCEDURE:

  1. Thoroughly hot water extraction rinse carpet. Leave carpet as dry as possible using multiple vacuum only wand strokes and blot dry with towel.
  2. Apply mixed solution of Stain Magic to stained fibers.
  3. Apply Dry Citric Acid evenly over treated fibers.
  4. Place DCI Light (Chemical Activation Bulb) over stains fibers and allow dwell time (up to 8 hours, DCI Light will increase effectiveness of stain removal).
  5. When stain disappears hot water extraction rinse carpet to remove residue.

TOOLS REQUIRED: HWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

TOOLS REQUIRED: HWE and a pump sprayer.

CHEMICALS REQUIRED: Last Step Rinse and CSS (Color Stabilizer and Souring Agent).

PROCEDURE:

This yellowing effect most frequently results from several sources:

  1. Cleaning with a solution that is too caustic (too high a P.H.).
  2. Alkaline off gassing from concrete being prevented from carpet.
  3. From water damage.
  4. To correct the discoloration:
  5. Thoroughly hot water extraction rinse the carpet with a solution of Last Step Rinse. Leave carpet as dry as possible.
  6. Apply a dilute solution of CSS with a pump sprayer.

 

Tip: Groom carpet and allow to dry before use. Discoloration should disappear as carpet dries.

TOOLS REQUIREDHWE and Carpet Shark

CHEMICALS REQUIRED: Pro-Zyme (Enzyme Spotter) Stain Magic (Oxidizer), and Stain Blotter (possibly)

PROCEDURE:

IMPORTANT: Do not use high temperature cleaning or heat activated stain removal procedures on these types of stains.

  1. Mix Pro-Zyme according to directions on bottle.
  2. Apply solution to stained fibers to thoroughly wet fibers.
  3. Gently but thoroughly agitate fibers to break up and emulsify deposit. Dwell time will help the biochemistry work for you here.
  4. Thoroughly rinse via water extraction leaving carpet as dry as possible (do not use an acid rinsing agent here).
  5. Apply Stain Blotter powder to absorb any wicking that might occur during drying.
  6. When spot is completely dry, vacuum thoroughly.

SUGGESTIONS AND CAUTIONS:

Also, you may experience wicking on heavier deposits. If deposit is heavy enough to have soaked through backing and into pad, replace the contaminated pad and clean carpet backing as outlined in Steps 1 through 5 above.

 

Wicking can be corrected by using an absorbent powder such as Stain Blotter. Simply cover spot liberally with Stain Blotter following your stain removal process. The wicking will go into the Stain Blotter and can then be vacuumed away when dry.

 

TIP: Stain 1 will make most re-occurring stains disappear.

Reduce/Oxidize:
Protein Spotters:
Dissolve/Emulsify:
Acid/pH Shift:

No products in the cart.

X